Yard Air Connections - Enclosure Boxes, Plumbing Pipes, Angle Cock Valves, Air Hoses And Glad Hands

Discussion in 'Right of Way' started by geep07, Aug 25, 2019.

  1. geep07

    geep07 Member

    Is there a detailed drawing for a yard air connection?

    These where located in major yards to provide air for the long string of cars.
     
    Last edited by a moderator: Jan 16, 2024
    modeltruckshop likes this.
  2. If you need pictures of a modern one as a reference I can do that.

    If nothing else surfaces.
     
    Last edited by a moderator: Jan 16, 2024
    mountaincreekar likes this.
  3. geep07

    geep07 Member

    Take what I can get!

    Thanks!
     
    modeltruckshop likes this.
  4. William Jackson

    William Jackson Bill Jackson

    The ones I saw on the Frisco had a metal box, 10" by about 15" with a cut off valve and a glad hand.

    Most had a lid, but rarely was it closed. The location was anywhere they wanted to keep from doing extra air tests. I have just seen them roll up a air compressor, also. Mainly they were used to meet FRA air tests, so the crew didn't have to do them. The Car Toads would do the testing, so the crew can roll out of here.

    Not much to see, the long tracks had some on the east end. I would need to look at the FRA book, not sure from memory, the requirements. Isn't retirement fun, I forget more of the rules each passing month. If you want to go through the requirements, get a CFR-49.

    On a more personal note I got a MRI, on my lower back lumbar. I have two disc's bulging one each way. I use pain med's for my neck fusion, and high doses of Steroids, so didn't notice much pain until it got to this point.

    I've been talking with doctor's so long about BP, dizziness and balance, finally I insisted on the MRI. No wonder I've been screwed up. It's frustrating, so if I have offended anyone, in the last few years, it was not intentional. We will see how it goes, but I should improve.

    Steroids, at the levels I take will make a person irritable and nuts.
     
    Last edited by a moderator: Jan 16, 2024
  5. geep07

    geep07 Member

    Bill,

    Where, were these metal box located?

    Between the rails and end of a yard track?
     
    Last edited by a moderator: Jan 16, 2024
    Ozarktraveler likes this.
  6. William Jackson

    William Jackson Bill Jackson

    Generally, the wrong place.

    Tracks were extended, trains got longer, hoses were laying between the track. Most of those boxes were between tracks. Items between the rail, eventually wound up tamped under a tie, or destroyed by track equipment.

    I think it was 1975, I ran a track cleaner through the Springfield yard. Ghastly job, looked like a tornado, moving down the track. We used a full time switcher to empty the air dumps. It had wings to smooth in between the tracks. It was a air box getter.

    Then tracks were widened, in the mid 1970s I got in on that job. They had a string of drop end gondolas and it just so happened a Speed Swing could drive right through them. Loaded with ballast, it moved at a slow speed and I would swing a bucket of rock to the side and dump it in between the track. So you know what I mean about the boxes being in the wrong place. Seemed anywhere was not a good place.

    At one time those boxes were painted yellow.
     
    Last edited by a moderator: Jan 16, 2024
  7. John,

    You can see there is not much to the one.

    The air supply pipe just sticks out of the ground and the hose attaches off that.

    The track location is painted to make it easier to spot.
     
    Last edited by a moderator: Jan 16, 2024
    gjslsffan and Ozarktraveler like this.
  8. gjslsffan

    gjslsffan Staff Member Staff Member

    In the yards that I have worked in that had them, there was a metal pipe inside the rail towards the end of some yard tracks.

    Many times these rails were painted to indicate where they were located Then there was a 30-40 foot hose at the end along with a sort of ball valve to turn the supply on and off. That's a neat little detail you don't see modeled very much, to be honest I hadn't thought about it at all.

    Another place you will find these is at larger industries or customers where entire trains are picked up, or when the contract calls for cars to be picked that are to be pre-tested "class 1, or initial terminal". Just for info, even if cars have been pre-tested, they will have to be re-tested if they are off air for over 4 hours.

    I have picked up trains at industries or yards that the headend power was on 1 track, and the rest of the train on an adjacent track, with a hose connecting the brake pipe on the front of the power connected to the other track to keep it all "on air".
     
    Last edited by a moderator: Jan 16, 2024
  9. The one pictured here is on a pretty good sized siding where the local makes up trains not made up in the yard.

    It is by Whirlpool appliance which uses rail. Plus UTLX has a large tank car facility here for repairs and rebuilds. So quite a bit of what sits there is home for repair tank cars waiting to get run into their repair plant.

    That track changes out once daily but anything tied up there has air on it.
     
    Last edited by a moderator: Jan 16, 2024
  10. klrwhizkid

    klrwhizkid Administrator Staff Member Administrator Frisco.org Supporter

    I found this on a Frisco Archive picture.

    Apparently a vertical pipe as a post (or a surge reservoir) with the air hose connected to it.

    Yard Air Pipe.jpg
     
    Last edited by a moderator: Jan 16, 2024
  11. Nice find Keith
     
    Ozarktraveler likes this.
  12. gjslsffan

    gjslsffan Staff Member Staff Member

    Frisco Autorack?

    HAHA
     
    Last edited by a moderator: Jan 16, 2024
    Ozarktraveler and modeltruckshop like this.
  13. gjslsffan

    gjslsffan Staff Member Staff Member

    Can you show the entire image.

    Looks like a locomotive servicing area to me in this image.
     
    Last edited by a moderator: Jan 16, 2024
    Ozarktraveler likes this.
  14. That’s funny.

    It is a cousin by merger Tom.
     
    Last edited by a moderator: Jan 16, 2024
  15. klrwhizkid

    klrwhizkid Administrator Staff Member Administrator Frisco.org Supporter

    It was.
     
    Ozarktraveler likes this.
  16. frisco1522

    frisco1522 Staff Member Staff Member

    Do you leave the yard air connected until the engine ties on?

    Don't want to get into a "bottling the air" situation.
     
    Last edited by a moderator: Jan 16, 2024
    Ozarktraveler likes this.
  17. William Jackson

    William Jackson Bill Jackson

    As Tom says, the four hour rule is in effect.

    It really don't take long to just pump them back up. But if you choose to bottle the air, it would only be a few seconds. Which has been done lots of times, they don't run off that quick. You do screw the air down on the engines, to not overcharge the train line. I have done it, but it's been a long time.

    When I was working in Denver, one time it got so cold in the Powder River basin that they sent me up to help. We drove along side the trains throwing wet paper towels on the glad hands, it would freeze and help retain trainline air. It was 35 below and wind chill was way colder.

    We also had a real time trying to close all the open rail joints. There was so much tiny snow and ice in the air that rainbows appeared. We burned those joints with rope to expand the rail, quite the site. Flames and diesel smoke rising in the air.

    Neat-o!
     
    Last edited by a moderator: Jan 16, 2024
  18. Coonskin

    Coonskin Member

    For what it is worth, by the time I retired in April 2018, any bottling of the air was a serious offense.

    Even after busting the air line, closing the angle cock on one end resulting in the angle cock being closed on both ends of the cut prior to a run-around could be viewed as "bottling the air". This trapping of trainline air could be a violation if viewed by a a railroad official or if a FRA agent was watching.

    They really got anal about it.

    Andre
     
    Last edited by a moderator: Jan 16, 2024
    gjslsffan and frisco1522 like this.

Share This Page